Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of FLEX NORYL™ Resin WCP921 - Asia - (PPE+TPE) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for FLEX NORYL™ Resin WCP921 - Asia:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Flex Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Product Texts
FLEX NORYL™ WCP921 resin is a high flow, flexible, non-reinforced injection moldable blend of Polyphenylene Ether (PPE) + Styrene Ethylene Butylene Styrene (SEBS) + Polyolefin. This material contains non-halogenated flame retardant and carries a UL94 flame rating of V0 at 6mm. FLEX NORYL WCP921 resin is intended for evaluation in over-molding applications such as plugs, strain reliefs, and connectors. It has a Shore A Hardness reading of 88 and exhibits low specific gravity, very low water absorption, and dimensional stability.

UL Yellow Card Link E207780-100123574
Processing/Physical CharacteristicsValueUnitTest Standard
ASTM Data
Melt Flow Index, MFI 17 g/10min ASTM D 1238
Temperature 250 °C -
Load 2.16 kg -
Mold Shrinkage, MD 0.55 mm/mm ASTM D 955
Mold Shrinkage, TD 0.65 mm/mm ASTM D 955
Mechanical propertiesValueUnitTest Standard
ISO Data
Stress at break 15 MPa ISO 527
Strain at break 50 % ISO 527
ASTM Data
Tensile Strength at Break 15 MPa ASTM D 638
Elongation at Break 150 % ASTM D 638
Shore A Hardness 88 - ASTM D 2240
Thermal propertiesValueUnitTest Standard
ISO Data
Burning behav. at thickness h V-0 class IEC 60695-11-10
Thickness tested 6.0 mm -
Glow Wire Flammability Index (GWFI) 850 °C IEC 60695-2-12
GWFI - thickness tested (2) 3 mm -
Glow Wire Ignition Temperature (GWIT) 725 °C IEC 60695-2-13
GWIT - thickness tested (3) 3 mm -
Electrical propertiesValueUnitTest Standard
ISO Data
Relative permittivity, 1MHz 2.8 - IEC 62631-2-1
Dissipation factor, 1MHz 290 E-4 IEC 62631-2-1
Comparative tracking index 600 - IEC 60112
ASTM Data
Volume Resistivity >1E15 Ohm*cm ASTM D 257
Other propertiesValueUnitTest Standard
Density 1040 kg/m³ ASTM D 792
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 60 - 80 °C -
Pre-drying - Time 4 - 6 h -
Processing humidity ≤0.01 % -
Melt temperature 220 - 250 °C -
Mold temperature 40 - 60 °C -
Zone 1 180 - 220 °C -
Zone 2 210 - 240 °C -
Zone 3 220 - 250 °C -
Screw speed 30 - 80 rpm -
Back pressure 3 - 10 MPa -
Characteristics
Processing
Injection Molding
Additives
Flame retarding agent
Special Characteristics
Flame retardant
Regional Availability
Asia Pacific
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.